Delta ts200ls Manual de Instruções

10" MotorizedBench Saw(Model TS200, Model TS200LS)Model TS200LSShownINSTRUCTION MANUALPART NO. A05738 - 05-19-05Copyright © 2005 Delta MachineryT

10ASSEMBLING STAND FOR MODEL TS200LS1. Assemble the stand as shown in Fig. 4C, using 16M8x1.25x20mm carriage head bolts, 3/8" flat washersand M8x

11Fig. 5Fig. 6Fig. 7ATTACHING BLADE HEIGHT ADJUSTING HANDWHEEL1. Insert an M6x1x55mm pan head screw (D) Fig. 5 through the handle (E). Attach the hand

12Fig. 14LBHCFig. 10Fig. 13Fig. 12Fig. 113. Locate the 1/4-20x2½" hex head screw (G) Fig. 10. Place the 1/4" internal tooth lockwasher (O) M

13Fig. 18Fig. 15Fig. 17Fig. 16NOTE: Before tightening the wing nut (M) Fig. 15,make certain a gap of at least 1/8" is between thebottom edge of t

14Fig. 24Fig. 26Fig. 25ASSEMBLING RIP FENCE1. Thread the M8x1.25 hex nut (A) Fig. 24, approximately halfway on the stud of the handle (B).2. Thread th

15BLADE HEIGHT ADJUSTMENTTo adjust the height of the saw blade, turn thehandwheel (A) Fig. 29. Turning the handwheel clockwiselowers the blade and tur

16Fig. 30ABBLADE TILT ADJUSTMENTTo tilt the saw blade, loosen the lock handle (A)Fig. 30 and move the handwheel (B) until the blade is atthe desired a

17RIP FENCE OPERATIONAND ADJUSTMENTS1. To move the rip fence (A) Fig. 33 along the table, liftup the fence locking lever (B), slide the fence to thede

18MITER GAUGE OPERATIONAND ADJUSTMENTSFor cross-cutting (blade set 90 degrees to the table), themiter gauge can be used in either table slot. For beve

19Fig. 381. NOTE: One 7/8" wrench is supplied with the saw forchanging the saw blade.2. Remove table insert (A) Fig. 38, and raise saw blade(F) t

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20Fig. 39AACBFig. 39BBor more to one side or the other depending on whichmiter gage slot is being used. This auxiliary wood-facing(B) can be fastenedt

21Fig. 42Fig. 43THE MAXIMUM WIDTH DADO CUT FORTHIS SAW IS 1/2 INCH.THE BLADE GUARD AND SPLITTERASSEMBLY CANNOT BE USED WHEN DADOING. ITMUST BE REMOVED

22Fig. 47Fig. 48Fig. 45 Fig. 46Fig. 44A1. Dadoing is cutting a rabbet or wide groove into thework. Most dado head sets are made up of two outsidesaws

23PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMATERIAL TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH

24Fig. 49Fig. 50Kerf should beabout 1/4" apart.TROUBLESHOOTINGFor assistance with your machine, visit our website at www.deltamachinery.com for a

25MAINTENANCEPARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a

26NOTES

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5ADDITIONAL SPECIFIC SAFETY RULESSAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. FAILURE TO FOLLOW THESE RULES MAY RESUL

66A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp t

7FUNCTIONAL DESCRIPTIONNOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRATES THECURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS CONTAINEDIN THE MANUAL

818971036245Fig. 41. Leg (4)2. 3/8” Flat Washer for Mounting Saw toStand & for Assembling Stand (24)3. Foot (4)4. M8x1.25 Hex Nut for Mounting S

9UNPACKING AND CLEANINGCarefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainte