INSTRUCTION MANUALESPAÑOL: PÁGINA 25To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com.For Parts, Service, Warranty or o
104. Attach the fence slide support (E) Fig. 7D, to theextension table (B) by using the two 5/16-18 x1 1/4”long hex head screws, 5/16” lockwashers and
11Fig. 11BFig. 10AAAAAFig. 9FASTENING MACHINE TO SUPPORTING SURFACEBefore operating your compound miter saw, firmly mountit to a workbench or other su
12Fig. 12ABFig. 13CDEB1. The compound miter saw will cut any angle from astraight 0° cut to 47° right and left. Turn locking knob(A) Fig. 12 countercl
13Fig. 15CBFig. 16GFDAFig. 17AAADJUSTING FENCE 90° TO BLADEIMPORTANT: BEFORE MAKING THIS ADJUSTMENT,SET THE BLADE AT 0° TO THE TABLE. SEE SECTION“ADJU
14Fig. 20Fig. 21BATILTING CUTTINGHEAD FOR BEVELCUTTINGIMPORTANT: MOVE THE SLIDING FENCE TO THELEFT TO PROVIDE CLEARANCE FOR THEBLADE AND GUARD. THE DE
15Fig. 24HCBFig. 25AFig. 26FEFig. 22Fig. 23BAAADJUSTING CHIP DEFLECTOR1. DISCONNECT THE MACHINE FROMTHE POWER SOURCE.2. A chip deflector (A) Fig. 22,
16Fig. 27CABACDFig. 28Fig. 29ABCADJUSTING SLIDING FIT BETWEENTRUNNION AND BEVEL BRACKETAfter a long period of time, it may become necessary toadjust t
17The TwinLaser™laser units are mounted in a housing that isfitted into the upper blade guard of the miter saw (Fig. A). Thelasers project a beam of l
18LEFT LASERADJUSTMENTSCREWFig. HFig. GFig. FTO CHECK FOR VERTICAL ALIGNMENT 1. The vertical alignment is set correctly when the linesdo not move hor
19CUTTING ALUMINUMAluminum extrusions (aluminum screens and stormwindows) can easily be cut with your miter saw. Whencutting aluminum extrusions, or o
2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic
20Fig. 34Fig. 35CORRECTINCORRECTFig. 36CBACFor support when cutting long pieces, construct a worksupport extension. Fig. 36 illustrates the miter saw
21CUTTING CROWN MOULDINGOne of the many features of the saw is the ease of cutting crown moulding. The following is an example of cutting bothinside a
22Fig. 41Fig. 42EBGCADHFig. 43FFig. 45BCFig. 44ACHANGING THE BLADEUSE ONLY CROSS-CUTTING SAWBLADES. DO NOT USE BLADES WITH DEEPGULLETS AS THEY CAN DEF
23KEEP TOOL CLEANPeriodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth. NEVER usesolvents to
The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de
3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation
4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed
5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.1. DO NOT OPERATE THIS MACHINE UNTIL it isassembled and installed according to th
6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti
7EXTENSION CORDSUse proper extension cords. Make sureyour extension cord is in good condition and is a 3-wireextension cord which has a 3-prong ground
8UNPACKING1. Carefully remove the machine from the carton.Retain all packing materials until you have inspectedand satisfactorily operated the machine
9MOVING TABLE TO THE 0° CUT-OFFPOSITION1. Rotate locking knob (A) Fig. 6 counter-clockwise asfar as it will go. Depress lever (B) and rotate table (C)
Comentários a estes Manuais