Delta DP350 Manual de Instruções descarregar pdf (Página 14)

TROUBLESHOOTING

For assistance with your machine, visit our website at www.deltaportercable.com for a list of service centers or call the

DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

MAINTENANCE

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp

cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the

outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION & RUST PROTECTION

Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially

available protective product designed for this purpose. Follow the manufacturer’s instructions for use and safety.

To clean cast iron tables of rust, you will need the following materials: a sheet of medium Scotch-Brite™ Blending Hand

Pad, a can of WD-40

and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad.

Degrease the table, then apply the protective product as described above.

Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at

servicenet.deltamachinery.com.

You

can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to

receive personalized support from highly-trained technicians.

FREE WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call

1-800-223-7278

for a free replacement.

A21575

ADJUST SPEED ONLY WHILE

MACHINE IS RUNNING.

AJUSTE LA VELOCIDAD SOLAMENTE

MIENTRAS LA MÁQUINA ESTÉ EN

FUNCIONAMIENTO.

RÉGLER LA VITESSE UNIQUEMENT

LORSQUE L'APPAREIL EST

EN MARCHE.

TO REDUCE THE RISK OF INJURY READ

INSTRUCTION MANUAL BEFORE OPERATING

DRILL PRESS. ALWAYS WEAR EYE PROTECTION

AND WEAR PROPER RESPIRATORY

PROTECTION. DO NOT WEAR GLOVES,

NECKTIES, JEWELRY, LOOSE CLOTHING OR

LONG HAIR. ALWAYS CLAMP WORKPIECE OR

BRACE IT AGAINST COLUMN TO PREVENT

ROTATION. KEEP HANDS AWAY FROM ROTATING

BIT OR ACCESSORY. USE RECOMMENDED

SPEED FOR THE DRILL AND WORKPIECE

MATERIAL. BE SURE DRILL BIT OR CUTTING

TOOL IS NOT DAMAGED AND PROPERLY

LOCKED IN THE CHUCK BEFORE OPERATING.

MAKE CERTAIN CHUCK KEY IS REMOVED

BEFORE STARTING DRILL PRESS. DISCONNECT

MACHINE FROM POWER SOURCE BEFORE

MAKING REPAIRS OR ADJUSTMENTS. DO NOT

EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.

PARA REDUCIR EL RIESGO DE LESIONES LEA EL MANUAL

DE INSTRUCCIONES ANTES DE OPERAR LA PRENSA DE

TALADRO. SIEMPRE UTILICE PROTECCIÓN PARA LOS OJOS

Y PROTECCIÓN PARA LA RESPIRACIÓN. NO USE

GUANTES,

CORBATAS, JOYAS, ROPA HOLGADA NI EL

CABELLO

LARGO. SIEMPRE SUJETE LA PIEZA DE TRABAJO

CON

ABRAZADERAS O AMÁRRELA CONTRA LA COLUMNA

PARA EVITAR LA ROTACIÓN. MANTENGA LAS MANOS

LEJOS DE LA BROCA O ACCESORIOS GIRATORIOS. USE LA

VELOCIDAD RECOMENDADA PARA EL TALADRO Y EL

MATERIAL DE LA PIEZA DE TRABAJO. ASEGÚRESE DE QUE

LA BROCA DEL TALADRO O LA HERRAMIENTA DE CORTE

NO ESTÉN DAÑADAS Y DE QUE ESTÉN CORRECTAMENTE

BLOQUEADAS EN EL PORTABROCAS ANTES DE SU

OPERACIÓN. ASEGÚRESE DE RETIRAR LA LLAVE DE

PORTABROCAS ANTES DE ENCENDER LA PRENSA DE

TALADRO. DESCONECTE LA MÁQUINA DE LA FUENTE DE

ALIMENTACIÓN ANTES DE REALIZAR REPARACIONES O

AJUSTES. NO EXPONGA A LA LLUVIA NI UTILICE EN

LUGARES HÚMEDOS.

POUR RÉDUIRE LE RISQUE DE BLESSURES, LIRE LE MODE

D’EMPLOI AVANT L’UTILISATION DE LA PERCEUSE À

COLONNE. TOUJOURS PORTER UNE PROTECTION

OCULAIRE ET DES ARTICLES DE PROTECTION DES VOIES

RESPIRATOIRES. NE PAS PORTER DE GANTS,

CRAVATES, DE BIJOUX NI DE VÊTEMENTS AMPLES;

COUVRIR LES CHEVEUX LONGS. TOUJOURS FIXER LA

PIÈCE OU BIEN LA CALER CONTRE LA COLONNE POUR

EMPÊCHER UNE ROTATION. TENIR VOS MAINS ÉLOIGNÉES

DE LA MÈCHE ROTATIVE OU ACCESSOIRE. UTILISER LA

VITESSE RECOMMANDÉE POUR LA PERCEUSE ET LE

MATÉRIEL DE LA PIÈCE À PERCER. S’ASSURER QUE LA

MÈCHE OU L’ORGANE DE COUPE N’EST PAS ENDOMMAGÉ

ET QU’IL EST BIEN VERROUILLÉ DANS LE MANDRIN AVANT

SON UTILISATION. S’ASSURER DE RETIRER LA CLÉ DU

MANDRIN AVANT DE DÉMARRER LA PERCEUSE DE

COLONNE. DÉBRANCHER LA MACHINE DE LA SOURCE

D’ALIMENTATION AVANT D’EFFECTUER DES RÉPARATIONS

OU DES RÉGLAGES. NE PAS L’EXPOSER À LA PLUIE ET NE

PAS L’UTILISER DANS UN ENDROIT HUMIDE.

A21573

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 43 44

Comentários a estes Manuais

Sem comentários

Delta DP350 Manual de Instruções Página 14

Comentários a estes Manuais

Manuais e produtos relacionados com Berbequins elétricos Delta DP350