Delta MS150 Manual de Instruções

Consulte online ou descarregue Manual de Instruções para Ferramentas elétricas Delta MS150. Delta MS150 Instruction manual Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 17
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
8 1/4"
Compound Miter Saw
(Model MS150)
INSTRUCTION MANUAL
PART NO. 905589 - 08-26-03
Copyright © 2003 Delta Machinery
ESPAÑOL: PÁGINA 17
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Vista de página 0
1 2 3 4 5 6 ... 16 17

Resumo do Conteúdo

Página 1 - Compound Miter Saw

8 1/4" Compound Miter Saw(Model MS150)INSTRUCTION MANUALPART NO. 905589 - 08-26-03Copyright © 2003 Delta MachineryESPAÑOL: PÁGINA 17To learn mor

Página 2 - GENERAL SAFETY RULES

10ADJUSTING SPRING PRESSURE OF TABLEPOSITIVE STOPThe rotating table has positive stops at the 90 degreestraight cut-off position and 22-1/2, 30, and 4

Página 3

111. Your machine has the capacity to cut standard 2 x 4’s lying flat or on edge, at the 45 degree right and left miter angles(Fig. 27A).2. A standard

Página 4 - SAVE THESE INSTRUCTIONS

12CUTTING BOWED MATERIALBefore cutting flat pieces, check to see if the material is bowed. If it is, make sure the material is positioned on the table

Página 5 - FUNCTIONAL DESCRIPTION

13Make sure that the fence is clear of the guard and blade before operating the saw.DCFig. 33Fig. 32BAFig. 34Fig. 35BDACCHANGING THE BLADEUse only cro

Página 6 - CARTON CONTENTS

4. Remove the outside blade flange (F) Fig. 38 and sawblade (G).5. To install a new blade, make sure that the insideblade flange (H) Fig. 39 is on the

Página 7 - ATTACHING DUST BAG

1515PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof

Página 8 - IN DOWN POSITION

16Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine

Página 9 - ADJUSTMENTS

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®, BAM-MER®, B.O.S.S.®, Build

Página 10 - POSITIVE STOP

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Página 11 - GENERAL CUTTING OPERATIONS

33GENERAL SAFETY RULES1. FOR YOUR OWN SAFETY, READ THE INSTRUC-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations

Página 12 - CUTTING CROWN MOULDING

4ADDITIONAL SAFETY RULES FORMITER SAWSRefer to them oftenand use them to instruct others.FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.04

Página 13 - MAINTENANCE

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Página 14

For your own safety, do not connectthe miter saw to the power sourceuntil the machine is completelyassembled and you read and under-stand the entire o

Página 15 - ACCESSORIES

7ATTACHING DUST BAGAttach dust bag assembly (A) Fig. 10 to dust spout (B) on rear of upper guard assembly.FASTENING MACHINE TO SUPPORTING SURFACEBefor

Página 16

TILTING CUTTINGHEAD FOR BEVEL CUTTINGLoosen the bevel cutting lock handle (A) Fig. 15. Tilt cutting-head to the desired bevel angle, and tighten the l

Página 17 - • DELTA)

9Fig. 18Fig. 19ABCCADJUSTING FENCE 90 DEGREES TO BLADEDISCONNECT MACHINE FROM POWER SOURCE.1. Place the cutting arm in the 90 degree straight cut-off

Comentários a estes Manuais

Sem comentários