Delta D25886 Manual do Utilizador Página 206
- Página / 339
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
4. Motion Control Instructions
DVP-MC operating manual 4-165
4.8. Explanation of G Codes and Coordinate Motion Instruction
4.8.1. G Code Input Format
G codes that 10MC supports and the input format:
G Code Function Format
G0 Rapid positioning N_G0 X_Y_Z_A_B_C_P_Q_
G1 Linear interpolation N_G1 X_Y_Z_A_B_C_P_Q_ E_E_ F_
N_G2 X_Y_Z_A_B_C_P_Q_I_J_T_E_E_F_
N_G2 X_Y_Z_A_B_C_P_Q_I_K_T_E_E_F_
N_G2 X_Y_Z_A_B_C_P_Q_J_K_T_E_E_F_
G2
Clockwise circular/ helical
interpolation
N_G2 X_Y_Z_A_B_C_P_Q_R_T_ E_E_ F_
N_G3 X_Y_Z_A_B_C_P_Q_I _J_T_ E_E_F
N_G3 X_Y_Z_A_B_C_P_Q_I_ K_T_ E_E_F
N_G3 X_Y_Z_A_B_C_P_Q_J_K_T_ E_ E_F
G3
Anticlockwise circular/
helical interpolation
N_G3 X_Y_Z_A_B_C_P_Q_R_T_ E_ E_ F_
G4 Dwell instruction N_G4 K_
G36
Set/Reset
N_G36 M0 K1
N_G36 M0 K0
G37 Status judgment
N_G37 M_ K1
N_G37 M_ K0
G17
XY plane selection
N_G17
G18
ZX plane selection
N_G18
G19
YZ plane selection
N_G19
G90 Absolute mode N_G90
G91 Relative mode N_G91
Note:
The underline in the format box refers to the parameter value to be set. When inputting G codes in the CNC
program in the CANopen Builder software, N_ should be input to the left of G code; N_ means the row
number of G code in the NC program; only one G code can be input in one row. The input format of G code in
the CANopen Builder software: N0 G0 X100 Y100
- DVP-MC Bus-Type 1
- Multi-Axis Motion Controller 1
- Operating Manual 1
- Content 2
- Overview of DVP10MC11T 7
- 2. System Function 10
- 3. System Installation 34
- 4.1. Instruction Table 42
- 4.2. Axis Status 46
- 4.3. Instruction Usage 47
- Instruction format 47
- Data type list 48
- 4.4.1. MC_MoveAbsolute 49
- Program Example (1) 52
- Program Example (2) 53
- 4.4.2. MC_MoveRelative 55
- 4.4.3. MC_MoveAdditive 59
- 4.4.4. MC_MoveSuperImposed 63
- 4.4.5. MC_MoveVelocity 68
- 4.4.6. MC_Stop 71
- 4.4.7. MC_PassiveHome 74
- Example 75
- 4.4.8. MC_Power 77
- 4.4.9. MC_Reset 78
- Exmaple: 79
- 4.4.10. MC_ReadStatus 80
- 4.4.12. MC_ReadAxisError 82
- 4.4.13. DMC_ReadParameter 83
- 4.4.14. DMC_WriteParameter 84
- 4.4.15. DMC_SetTorque 85
- Program Example 86
- 4.5.1. MC_CamTableSelect 87
- 4.5.2. MC_CamIn 88
- = 0, slave position is 101
- 0, slave offset = 0 102
- Master Positio 102
- offset = 40, slave position 103
- Electronic cam example: 104
- Position 105
- 4.5.3. MC_CamOut 107
- Program Example: 108
- 4.5.4. DMC_CamSet 110
- Acceleration 112
- 4.5.5. MC_GearIn 114
- . UINT D 115
- 4.5.7. MC_Phasing 118
- Sequence Diagram 120
- 4.5.8. DMC_CapturePosition 121
- 4.5.9. DMC_VirtualAxis 127
- 4.5.10. DMC_ExternalMaster 129
- 4.6. Logical Instruction 131
- 4.6.3. ADD_R 132
- 4.6.4. SUB 132
- 4.6.5. SUB_DI 133
- 4.6.6. SUB_R 133
- 4.6.7. MUL 134
- 4.6.8. MUL_DI 134
- 4.6.9. MUL_R 135
- 4.6.10. DIV 135
- 4.6.11. DIV_DI 136
- 4.6.12. DIV_R 136
- 4.6.13. AND 137
- 4.6.14. OR 137
- 4.6.15. XOR 138
- 4.6.16. NOT 138
- 4.6.17. CTU 139
- Program example: 140
- 4.6.18. CTD 141
- 4.6.19. CTUD 143
- 4.6.20. TON_s 145
- 4.6.21. TOF_s 147
- 4.6.22. TONR_s 149
- 4.6.23. TON_ms 151
- 4.6.24. TOF_ms 152
- 4.6.25. TONR_ms 153
- 4.6.26. CMP 154
- 4.6.27. CMP_DI 155
- 4.6.28. CMP_R 156
- 4.6.30. MOV_DI 158
- 4.6.31. MOV_R 158
- 4.6.34. MOVF_R 161
- Program example : 162
- 4.6.36. MOV_BW 163
- 4.6.38. ZCP 165
- 4.6.39. ZCP_DI 166
- 4.6.40. ZCP_R 167
- 168
- 4.6.43. OUT 169
- 4.6.44. R_Trig 169
- 4.6.46. ZRSTM 172
- 4.6.47. ZRSTD 173
- 4.6.48. SQRT_R 174
- 4.6.49. MOD 174
- 4.6.50. MOD_DI 175
- 4.6.51. MOD_R 175
- 4.6.52. Real_To_Int 176
- 4.6.53. Real_To_DInt 176
- 4.6.54. Int_To_Real 177
- 4.6.55. DInt_To_Real 177
- Example 1: 178
- Example 2: 179
- Example 3: 179
- 4.6.58. Offset _R 182
- 4.7. Application Instruction 183
- 4.7.2. Rotary Cut Parameters 184
- Short material cutting 185
- Equal length cutting 185
- The entry curve 187
- The end curve 188
- 4.7.5.1 189
- 4.7.5.2. APF_RotaryCut_In 191
- 4.7.5.3. APF_RotaryCut_Out 192
- Explanation of areas 197
- Steps for flying shear 197
- Function feature 197
- Shear axis 198
- Sync area 203
- 4.8.1. G Code Input Format 206
- Center of a circle 222
- Start point 222
- Terminal point 222
- （）200,200 223
- Start point Start point 226
- Instruction example 1: 232
- Instruction example 2: 232
- Instruction example: 232
- 4.8.4. DMC_NC 233
- Program example 1: 235
- Program example 2: 236
- ¾ Program: 237
- ¾ Steps: 237
- 5.Troubleshooting 258
- 5. Troubleshooting 259
- Appendix A 264
- Appendix B 287
- Appendix C 301
- Appendix D 333
- Appendix E 338
Manuais e produtos relacionados com Compressores de ar Delta D25886
Compressores de ar Delta D25886 Manual de Instruções
(72 páginas)
(72 páginas)
Compressores de ar Delta A08590 Manual de Instruções
(24 páginas)
(24 páginas)
Compressores de ar Delta 66-750 Manual de Instruções
(30 páginas)
(30 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 4.908 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais