Delta TS300 Manual de Instruções

INSTRUCTION MANUALPART NO. A06547 - 12-31-04Copyright © 2004 Delta MachineryESPAÑOL: PÁGINA 27To learn more about DELTA MACHINERY visit our website at

10ATTACHING THE SAW TO THE STAND1. Invert the saw table face down on a piece of cardboardto protect the table surface. Align the four holes in thesaw

11CHANGING THE BLADEUse only 10" diameter saw blades, rated for 6000 rpm or higher with 5/8" arbor holes.DISCONNECT THE MACHINE FROM THE POW

121. Align the three slotted holes in the front right guide rail (A) Fig. 14 with the two holes (B) in the saw table and the slottedhole (C) in the ex

131. Insert the handle (A) Fig. 19 into the threaded hole (B) in the rip fence (C).2. Insert a flat-head screwdriver into the rip fence handle (A) Fig

14BLADE GUARD AND SPLITTER ASSEMBLYDISCONNECT THE MACHINE FROM THE POWER SOURCE.1. Thread an M12 x 1.75 hex nut (A) Fig. 26 on the splittersupport rod

15OPERATIONSTARTING AND STOPPING THE SAW1. The on/off switch (A) Fig. 30 is located on the front of panel of the saw. To turn the machine “ON”, move t

16ADJUSTING 90° AND 45° POSITIVE STOPSYour saw is equipped with positive stops that will position the saw blade at 90° and 45° to the table. To check

171. To move the fence (A) Fig. 38 along the guide rails, lift up on the fence locking lever (B), slide the fence to the desiredlocation, and push dow

18MACHINE USE3. The miter gauge is equipped with a special washer (F) Fig. 42, and a flat head screw (G) which are attached to the bottomend of the mi

19RIPPINGRipping is the operation of making a lengthwise cut througha board (Fig. 46), and the rip fence (A) is used to positionand guide the work. On

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20For certain cutting operations such as dadoing and moulding where you are not cutting completelythrough the workpiece, DO NOT USE the blade guard an

21Dadoing is cutting a rabbet or wide groove into a workpiece.Most dado head sets are made up of two outside saws andfour or five inside cutters (Fig.

22When performing a moulding operation,add a wood facing (A) Fig. 57 to one or both sides of therip fence. Attach the wood facing to the fence with wo

23PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN the WIDTHOF THE WORKPIECE.When ripping work less than 4" wide, use a push

24TROUBLESHOOTINGFor assistance with your tool, visit our website at www.deltamachinery.com for a list of service centers or call theDELTA Machinery h

25PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

26Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SAFETY RULESFOR TABLE SAWSSAVE THESE INSTRUCTIONS. Refer to them often

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

7EXTENSION CORDSUse proper extension cords. Make sureyour extension cord is in good condition and is a 3-wireextension cord which has a 3-prong ground

81. Table Saw2. Extension Wing (2)3. Rip Fence4. Miter Gage5. Rip Fence Handle6. Handwheel (2)7. M10 Flat Washer (2), Used to mounthandwheel lock knob

9For Saw Stand1. Top Front and Rear Braces - 19" in length(2)2. Bottom Front and Rear Braces - 22-1/2"in length (2)3. Stand Legs (4)4. Feet