Delta 17-950L Manual do Utilizador

www.deltamachinery.com(800) 223-7278 - US(800) 463-3582 - CANADA10" Contractors Saw(Model 36-978/36-979)Taladro de bancode 432 mm(16-1/2 pulg)con

103" MINIMUM3" MINIMUM3" MINIMUM3" MINIMUM28" MINIMUM21" MINIMUM1. If you plan to use your drill press in a permanent l

RISK OF UNSAFE OPERATION. You must secure the plywood base to the floor or supporting surface if the drill press has any tendency to vibrate, slide,

12EYE INJURY - LASER LIGHT. Do not stare into the laser beam or aperture or into a reflection from a mirror-like surface.14. Use the two socket head

13IMPORTANT: Make certain the spindle taper (O) Fig. 14, and tapered hole in chuck (P) are clean and free of any grease, lacquer or rust preventive co

1424. Align the two holes in the lamp bracket (A) Fig. 17, with the two holes (B) on the side of the drill press head.25. Place the cord bushing (C) F

15 FIRE HAZARD. To reduce the risk of fire, use 40 watt or less, 120 volt, reflector track type light bulb (not supplied). DO NOT USE a stan dard hou

16TABLE INSERTThe drill press table comes with an insert (H) Fig. 26 made of MDF to help prevent wear and tear on the bit when it drills down through

17MAKING THE LASERS INTERSECT1. Place a piece of wood (A) Fig. L4 on the table and clamp it in place.2. Use the handle (B) to lower the quill (C).

181. Open the belt and pulley guard (A) Fig. 28B.2. Loosen the tension lock knobs located on both sides of the head casting (one shown at (B) Fig. 2

19NOTE: Use bits with this drill press that have a shank of 5/8" or less in diameter. NOTE: Use scrap material for practice to get a feel of the

2TABLE OF CONTENTSTABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20DRILLING METALUse clamps to hold the workpiece. DO NOT try to hold the workpiece with your hand. The drill bit may seize the work at any time and sp

21MAINTENANCEREPLACEMENT PARTSUse only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.deltamachinery

22Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine

6464The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes s

3It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. Th

41. FOR YOUR OWN SAFETY, READ THE INSTRUCTION MANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations, and specific haza

5ADDITIONAL SPECIFIC SAFETY RULES1. DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machi

6ADDITIONAL SAFETY RULES FOR THE LASERFAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.EYE INJURY -LASER LIGHT* Do not stare into beam aper

7Fig. A Fig. BGROUNDED OUTLET BOXCURRENTCARRYINGPRONGSGROUNDING BLADEIS LONGEST OF THE 3 BLADESGROUNDED OUTLET BOXGROUNDING MEANSADAPTERPOWER CONNECTI

8FOREWORDThe Delta 17-950L drill press is a 16-1/2" drill press with a laser guide and a large woodworker's table (14x18 inches). The table

11. Drill Press Head2. Table3. Table Bracket and Column4. Light5. Base6. Chuck7. Handle (3)8. Spindle Adapter9. Drift Key10. 5mm Hex Wrench11. 3mm He